Pedal assist means the motor helps only while you pedal. Sensors read your pedaling, a controller adds motor power in proportion to the assist level you choose, and the help stops when you stop pedaling, brake or reach the bike’s cutoff speed (20 mph on a Class 1 bike). A throttle is different: it can move the bike with no pedaling at all. As a rule, use the lowest level that lets you hold a steady, comfortable effort, step up one or two levels for a headwind or a long hill, and keep the top level for short, steep climbs.
This guide explains the parts first, then turns them into decisions: a table for common situations, worked numbers for hills, wind and range, and a first-ride routine. Where each class of e-bike may ride is covered in the e-bike classes guide; this article sticks to how the bike behaves under you.
How pedal assist works: sensors, a controller and a motor
A pedal-assist e-bike has three working parts between your legs and the motor: sensors that read what you are doing, a controller that decides how much help to add, and the motor that adds it. The assist level you press on the handlebar is an instruction to the controller, not to the motor directly.
A September 2023 application brief from Texas Instruments, Position Sensing in e-Bike Applications (SLYA077), maps the sensors on a typical e-bike: wheel speed, cadence, torque, throttle and brake lever position, plus the motor’s own position sensors. Not every bike has all of them. Most riders only need to know what three of them do.
Cadence sensors: are you pedaling?
A cadence sensor tracks how fast the cranks turn. The TI brief says this signal tells the controller “that the rider is actively riding the bicycle,” and that many e-bikes require it before the motor engages. A traditional design is a magnetic switch (a Hall-effect latch) watching a ring of magnets on the chainring; more magnets mean less pedal movement before the motor starts.
A cadence signal says that the cranks are turning and how fast. It does not say how hard you are pushing. That is why a bike that relies on cadence alone tends to add a set amount of help for each level, whether you are pressing lightly or hard.
Torque sensors: how hard are you pushing?
A torque sensor measures the force you put into the cranks. TI describes two common designs: a strain gauge on the crank axle in the bottom bracket, or a flexing mount at the rear sprocket read by a magnetic sensor. In TI’s words, torque sensing gives “a more natural response and feel for the rider than is provided using cadence alone,” because the controller can set motor drive “with respect to the human energy output.”
A 2023 paper from National Taiwan University in the journal Sensors, Ho and colleagues, describes the same principle: on a cycling-assisted e-bike the motor torque output “is dependent on the human pedaling torque.” Push harder and the motor pushes harder, in the ratio your level sets.
The same paper lists what the rider and motor are working against together: the cyclist’s weight, wind resistance, rolling resistance and the road slope. Those four loads are why the right level changes with the road, and they come up again in the sections on hills, wind and range below.
What each type feels like from the saddle
You do not need to know which sensor a bike has to ride it, but it explains what you feel. On a bike that relies on cadence, the motor joins once the cranks have turned far enough to trigger the sensor, and then pushes at a fairly steady strength for the level you chose. Easing off the pedals without stopping may not change the help much.
On a torque-sensing bike, the help rises and falls with your own push from the first pedal stroke. TI notes that the torque reading gives the controller “instantaneous feedback from the rider.” Many riders find this easier to control at low speed, because a gentle push brings a gentle response.
TI also notes that combining wheel speed, cadence and torque gives the controller “a complete picture” of the rider’s effort. Some bikes use all three. If you ride an unfamiliar bike, a minute of slow riding in a quiet spot tells you which behavior you have.
Wheel speed and brake signals: when the help stops
A magnet on a spoke and a sensor on the fork count wheel turns, and TI notes that this speed signal can be used “to set maximum travel speeds.” That is how a Class 1 bike knows to stop helping at 20 mph. Wyoming defines a Class 1 electric bicycle in W.S. 31-1-101(a)(xxxiv) as one whose motor “provides assistance only when the rider is pedaling” and “ceases to provide assistance” at 20 mph.
Brakes matter too. Under W.S. 31-5-707(e), an electric bicycle must operate so that when the rider “stops pedaling, applies the brakes or the electric motor is disengaged, the electric motor assist ceases to function.” How a bike meets that rule is up to its maker; the TI brief, for example, describes magnetic sensors that can track brake lever position.
Pedal assist vs throttle: what changes on the road and in the law
Pedal assist adds to your pedaling; a throttle can replace it. In the three-class system Wyoming and Colorado use, Class 1 and Class 3 bikes are pedal-assist only, and a Class 2 bike has a motor that “may be used to propel the bicycle without pedaling,” with no assistance at 20 mph (W.S. 31-1-101(a)(xxxiv)).
The Jefferson County Sheriff’s Office in Colorado puts the difference in plain words on its e-bike page: Class 1 is “Must pedal to operate” and “No throttle,” while Class 2 is “Do not need to pedal” with “Throttle assist available.” The table below sets out what that means for a rider.
| Question | Pedal assist (Class 1) | Throttle (Class 2) |
|---|---|---|
| What starts the motor? | Turning the cranks | A thumb lever or twist grip, with or without pedaling |
| Can the bike move with no pedaling? | No | Yes |
| When does the help stop at speed? | 20 mph | 20 mph |
| What sets how much help you get? | Your pedaling and the assist level | How far you press the throttle |
| How it feels | Like a bicycle with a tailwind | Closer to a small motor vehicle when the throttle is on |
| Your share of the work | Always some, more at low levels | Can be none |
Why the difference matters for where you ride
Class decides where a bike may usually go, and local rules can treat classes differently. Boulder County says Class 1 and 2 bikes are “Generally permitted on bike lanes, and pedestrian and bike paths unless otherwise posted,” and allowed on designated regional and open space trails in the plains, while “All e-Bikes are prohibited on foothills and mountain trails.” Class 3 is “Allowed on streets and designated bike lanes” but prohibited on multi-use paths and open space trails, except the US 36 bikeway.
Jefferson County lists Class 1 and 2 as allowed on roads, trails and parks, and Class 3 on roads only. In both counties the 28 mph Class 3 bike is the one kept off most paths; Class 1 and Class 2 are treated alike. Cities, campuses and HOAs can set their own rules, so the e-bike classes guide points you to the Wyoming and Colorado rules and reminds you to check locally. This is general information, not legal advice.
The federal definition is about product safety, not where you ride
The federal rule most people quote is in the Consumer Product Safety Commission’s bicycle requirements. Under 16 CFR 1512.2(a)(2), a bicycle includes “a two- or three-wheeled vehicle with fully operable pedals and an electric motor of less than 750 watts (1 h.p.), whose maximum speed on a paved level surface, when powered solely by such a motor while ridden by an operator who weighs 170 pounds, is less than 20 mph.”
That definition decides which federal product safety rules apply to the bike. It does not decide where you may ride; state law and local rules do. Wyoming ties the two together by requiring that an electric bicycle comply with the federal bicycle requirements in 16 C.F.R. 1512 (W.S. 31-5-707(d)).
Why shared fleets often choose pedal assist
A shared bike carries confident cyclists and people who have not ridden for years, often on the same day. With pedal assist, the help depends on the rider’s own pedaling: a startled rider who stops pedaling also stops getting help, and there is no lever to press by accident while walking the bike out of a bay.
That is the reasoning behind Colibrino’s own specification, which is Class 1 only, with no throttle. Other programs make other choices, and some riders, including some with limited leg strength, may prefer a throttle on a bike they own. The choice is about who rides and where, not about one design being right for everyone.
Turning the level up does not change the class
An assist level changes how strongly the motor responds below the cutoff. It does not move the cutoff. On a Class 1 bike, the lowest and highest levels both stop helping at 20 mph, and the class printed on the frame label stays the same. Wyoming requires that label, with the class, top assisted speed and motor wattage (W.S. 31-5-707(b)), and forbids modifying a bike’s motor-powered speed or motor engagement unless the label is replaced (W.S. 31-5-707(c)).
What an assist level changes, and what it does not
An assist level sets how much the motor adds for each unit of your effort. It does not set your speed. It also does not change your brakes, the bike’s weight or the speed at which the help stops.
How many levels a bike has
There is no standard number. The Sensors paper, describing a control approach from earlier research, notes that “three to five different motor torque levels can be manually selected.” Some systems name their modes instead of numbering them: the Bosch eBike Systems range calculator, for example, lists ECO+, ECO, TOUR, TOUR+, AUTO, SPORT, eMTB, CARGO and TURBO. A “level 3” on one bike can feel nothing like “level 3” on another.
How much of the work stays with you
The clearest measure of a level is how much of the effort it takes off you. Researchers at the University of Twente measured riders on an indoor trainer with pedal assistance, using power meters in the pedals, heart rate monitors and oxygen masks; the university reported the results in May 2026. In the lowest setting (eco), riders used about 70 to 77 percent of the energy they would use on a standard bicycle.
At the highest setting (turbo), riders used about a quarter of that energy, and heart rate and oxygen uptake were “barely higher than at rest.” Movement scientist Jasper Reenalda summed it up: “On the highest setting, you’re doing very little yourself.” He added that 150 minutes a week of moderate exercise is achievable on eco mode, though you may need to ride further than on a normal city bike.
A 2022 meta-analysis in the Scandinavian Journal of Medicine and Science in Sports, McVicar and colleagues, reviewed 14 studies with 239 participants and pooled 12 of them. Compared with conventional cycling, riding with assistance lowered heart rate by about 11 beats per minute on average and the rider’s power output by about 31 watts.
What this means in practice
Think of the levels as a dial between “a bicycle that helps a little” and “a bicycle that does most of the work.” Low levels keep you warm, save battery and leave you in control of every surge. High levels flatten hills and headwinds but use the battery faster and leave you doing less.
Neither end is wrong. The right level is the one that fits the next few minutes of road, and it is normal to change level several times on a short trip.
Four common misreadings
“A higher level makes the bike faster.” Only up to the cutoff. A higher level gets you to a given speed with less effort, but on a Class 1 bike every level stops helping at 20 mph. Above that, you are riding a heavy bicycle on your own legs.
“Pedal assist means no exercise.” The Twente measurements show the opposite at low levels: riders on eco still used roughly three quarters of the energy they would on a standard bicycle. The exercise you get depends on the level you choose and how far you ride.
“The top level is safest on a hill.” Not always. The top level helps you keep speed on a steep pitch, but it also delivers the biggest surge on a restart or a slippery patch. A middle level with a low gear is often easier to control.
“Level numbers mean the same thing on every bike.” They do not. The number of levels, their names and the strength of each step are set by the drive system and the bike maker. On an unfamiliar bike, start at the bottom and work up.
Which assist level to use: a decision table
Start in the lowest level that lets you hold a steady effort, shift gears before you change level, and step up only when your pedaling slows and gearing down no longer helps. The table gives a starting point for common situations; adjust from there.
| Situation | Start at | Why | Battery use |
|---|---|---|---|
| Pulling away from a stop on flat ground | Low | A smooth start without a lurch | Small |
| Flat path, calm air | Low | You do most of the work and keep the longest range | Lowest |
| Gentle hill or a long, slow rise | Middle | Holds your cadence without straining | Moderate |
| Short, steep climb | High, for the climb only | Keeps speed up so the bike stays stable | High, briefly |
| Steady headwind | One or two steps above your flat level | Air drag rises with the square of airspeed | Higher |
| Tailwind | Lowest | The wind does part of the work | Lowest |
| Gusty crosswind | Low or middle, at a lower speed | Less surge to manage when a gust hits | Low |
| Cold morning | Low to start | Pedaling warms you; a cold battery has less to give | Gauge drops faster |
| Wet leaves, slush or ice | Lowest, or walk | Gentle force at the rear tire | Low |
| Crowded shared path | Lowest | Easy speed control near people on foot | Low |
| Carrying groceries in a basket | Middle | Extra weight adds to every climb and start | Higher |
| Long trip near the edge of your range | Low throughout | Saves charge for the end of the ride | Lowest |
| Riding for exercise | Lowest | More of the effort stays with you | Lowest |
Three rules behind the table
- Gears first, then assist. Shifting to an easier gear keeps your cadence up for free. Raise the level only when you are already in a low gear and still slowing.
- Hold an effort you could keep up for the whole ride. If you are breathing too hard to talk, step up one level. If you barely feel the pedals, step down.
- Choose control over speed where people, ice or gusts are around. A lower level gives you gentler surges and more time to react, which matters more than the minute you might save.
When to change level during a ride
Change before the situation, not in the middle of it. Raise the level a few yards before the foot of a hill, before you turn into a headwind, or before you pull away from a stop sign on a rise. Drop it as you crest the hill, turn downwind or reach a crowded path.
On most bikes the plus and minus buttons sit by your left thumb, and the display shows the level and the battery gauge. Learn where they are before you ride in traffic, so you can change level without looking down.
Climbing hills: gears first, then assist
On a hill, shift to an easier gear before the slope starts, raise assist one level at the foot if your cadence drops, and keep the top level for short, steep pitches. The motor shares the work of lifting you and the bike; the level decides how big its share is.
What a hill costs, in numbers
Climbing costs energy because you are lifting weight. For example, suppose a rider and bike together weigh about 100 kilograms (220 pounds) and climb 30 meters (about 100 feet). The energy needed just to lift them is weight times gravity times height: 100 × 9.81 × 30 = 29,430 joules, or about 8.2 watt-hours.
That is a physics floor, before rolling resistance, air drag and motor losses. For scale, the Colibrino range estimator uses 15 watt-hours per mile as a planning assumption for a lightweight pedal-assist bike at moderate assist on flat ground. The height of that one hypothetical climb costs about half of a flat mile’s budget.
Power tells you how hard the climb feels. Take the same hypothetical rider on a 6 percent grade at 8 mph (3.6 meters per second). The bike rises about 0.21 meters every second, which takes about 210 watts just for lifting, before any other losses. A higher assist level means the motor supplies more of those watts and you supply fewer.
Step by step: a steady climb
- Look ahead and shift to an easier gear before the slope starts.
- Raise assist one level a few yards before the climb.
- Keep your cadence up; spin lighter rather than push harder.
- If your cadence still falls, raise one more level instead of standing on the pedals.
- Stay seated so the rear tire keeps its grip.
- On the steepest part, keep pedaling smoothly; stopping on the pitch makes the restart harder.
- Drop back down a level as the slope eases, before the top.
Starting on a hill
If you have to stop partway up, choose an easy gear before you stop. To restart, put one pedal at about the two o’clock position, set a middle level, and press smoothly. A very high level on a steep restart can make the front of the bike feel light and the start feel jumpy, so a middle level is often easier to control.
Coming back down
Descents need no assist. Set the lowest level or switch assist off, keep both hands on the brakes, and brake before the steep part rather than on it. The motor stops helping at 20 mph on a Class 1 bike, but gravity does not, so speed on a long hill is yours to manage.
Example (fictional). In the fictional Larkspur Commons example network, a resident rides the typical 1.8-mile trip to a grocery store. The route is flat for a mile, then climbs a short, steep rise before the store. She starts in the lowest level, shifts down at the foot of the rise, steps up two levels for the steep part and back to low at the top. On the way home with a full basket, the rise is now a descent, so she sets the lowest level and brakes early. The trip uses little battery, and the bike goes back into its bay to charge.
Riding into wind: when to turn assist up
In a steady headwind, raise assist one or two levels to keep your cadence; in a tailwind, drop to the lowest level. In gusty crosswinds, slow down and keep assist low or middle, so a gust does not arrive at the same moment as a surge of motor power.
Why a headwind costs so much
Air resistance grows quickly with speed through the air. NASA’s Glenn Research Center explains in its drag equation that drag depends on the density of the air and “the square of the velocity.” For a rider, the velocity that counts is airspeed: your speed over the ground plus the headwind.
For example, suppose you ride at 12 mph into a 12 mph headwind. Your airspeed is 24 mph, twice what it would be on a calm day, so air drag is about four times as large. Holding the same 12 mph over the ground therefore takes about four times the power against the air. The same ride with a 12 mph tailwind leaves almost no air drag at all.
This is the physics; real riding adds rolling resistance, your position on the bike and the shape of your clothing. The point holds anyway: a headwind is often harder than a hill, and assist is the easiest way to keep your cadence steady through it.
Crosswinds and gusts
A crosswind does not slow you as much as it pushes you sideways. Gusts are the hazard: they hit at building corners, open intersections and gaps between buildings. Lower speed gives you more time to correct, and a lower assist level means less extra push at the moment you are steering against a gust.
Wind is a daily factor where Colibrino plans to work. The Wyoming State Climate Office notes that Wyoming ranks first in the US with an annual average wind speed of 12.9 mph, and that winter winds reach 30 to 40 mph with gusts of 50 or 60 mph. For when to ride, when to walk and when to leave the bike in its bay, read our guide to riding an e-bike in strong wind.
Assist level and range: the trade-off in numbers
Higher assist uses more watt-hours per mile, so range falls as the level rises. The relationship is simple: range equals usable battery energy divided by energy used per mile. What you control is the energy per mile.
The method, step by step
- Find the battery size in watt-hours (Wh). It is printed on most batteries; if only volts and amp-hours are shown, multiply them.
- Decide what share you plan to use. Keeping a reserve is sensible; the range estimator’s default is 90 percent.
- Estimate energy per mile at your usual level. The estimator’s default is 15 Wh per mile at moderate assist on flat ground, a planning assumption rather than a measurement.
- Divide usable energy by energy per mile.
With the estimator’s defaults (a 400 Wh battery, 90 percent of it used, 15 Wh per mile), range on a mild, calm, flat day is 400 × 0.9 ÷ 15 = 24.0 miles. Add the default allowance for cold (80 percent of capacity available) and 25 percent extra energy for wind, hills or load, and range today falls to 15.4 miles, or 8 trips of 1.8 miles. These are example figures in the tool, not the specification of any bike.
How the level changes the answer
Now hold everything else fixed and change only the energy per mile. For example, suppose a low level used 10 Wh per mile and the highest used 30 Wh per mile. The chart shows what that would do to range on the same 400 Wh battery.
The shape is what matters. Going from the lowest to the highest level in this hypothetical example cuts range to a third. On a short trip that barely registers; on a long ride it decides whether you get home with charge to spare.
Level is only one input
Range depends on much more than the level. The Bosch range calculator asks for riding mode, average speed, total weight with bike and luggage, cadence, type of bike and riding posture, stop frequency, terrain, wind conditions, shifting system, surface, tire tread and season. Bosch notes that its results are estimates and that values apply to a new battery, which ages like every lithium-ion battery.
That list is a useful checklist for your own riding. Frequent stops, a heavy load, soft tires, a fast average speed and cold weather all raise energy per mile at any level.
Measuring your own energy per mile
You can estimate your own number without special tools. Ride a familiar route of known length at your usual level, note how many gauge bars it used, and repeat on a different day or at a different level. Gauges are not precise, so treat the result as a rough guide and compare like with like.
Example (fictional). A rider plans a 6-mile round trip on a cold, windy morning with the range estimator. She keeps the tool’s 400 Wh battery and 90 percent share, uses the default 15 Wh per mile for her usual moderate level, and leaves the defaults of 80 percent capacity in the cold and 25 percent extra for wind. The estimate is 15.4 miles today, so 6 miles leaves a wide margin even if she rides the headwind leg two levels higher. If the gauge drops faster than expected on the way out, she drops a level on the tailwind leg home. All figures here are the tool’s example values, not the specification of a real bike.
In a shared fleet, range matters less than on a bike you own, because a station bike goes back into a charging bay after each ride. It still matters on cold days, windy days and long trips. Check the gauge before you unlock, and dock before the last bar.
Cold mornings, wet roads and ice
In cold weather, start in a low level and expect the battery gauge to drop faster than usual, because a cold battery delivers less energy. On wet leaves, slush or ice, use the lowest level or walk, because gentle force at the rear tire is easier to control than a surge.
Cold and the battery
The US Department of Energy’s fueleconomy.gov states plainly that “Battery performance decreases in cold weather” in its guide to fuel economy in cold weather. Its measured figures are for electric cars, which also heat a cabin, so they do not transfer directly to an e-bike. The direction does: the same assist level costs a larger share of a cold battery.
That is why the range estimator asks you for the share of capacity available at today’s temperature rather than guessing one. Its default, 80 percent, is an assumption to replace with your own observation from mild and cold days on the same route.
Why a low level helps on a cold start
A low level makes you pedal harder in the first minutes, which warms you up. It also leaves charge in reserve for the ride home, when the wind may have turned. Raise the level once you are warm and the route calls for it.
Cold also affects charging. Colibrino does not charge batteries while they are frozen, and its riders never charge batteries at home; the rider guide explains the rules, and our guide to riding an e-bike in winter covers snow, ice and clothing.
Slippery surfaces
On wet leaves, packed snow or ice, the rear tire can slip if force arrives suddenly. A torque-sensing bike adds force in step with your pedaling, and a low level keeps that force small. Start in a low gear, pedal smoothly, and avoid braking or turning hard on slick patches. On ice, the safest choice is usually to walk the bike or leave it in its bay.
First rides: a 15-minute practice routine
Learn the bike in an empty parking lot or a quiet path before you ride in traffic: start in the lowest level, practice starts, stops and turns, then try each level in turn. Harvard Health Publishing advises practice because “E-bikes are much heavier than conventional bicycles and may handle differently.”
The routine
- Check the bike. Battery gauge, tires, brakes, lights and seat height. The pre-ride checklist lists every item.
- Find the controls. Locate the plus and minus buttons, the display and both brake levers before you roll.
- Set the lowest level. Start with assist on, but at the bottom of the range.
- Practice starts. With one pedal at about two o’clock, press gently and notice how quickly the motor joins in.
- Practice stops. Squeeze both brakes evenly. Notice that the motor stops helping when you brake, as Wyoming law requires (W.S. 31-5-707(e)). If it keeps pushing, stop and report the bike.
- Practice coasting. Stop pedaling while moving and feel the help fade.
- Try each level. On a straight stretch, step up one level at a time and feel the difference in push. Step back down.
- Practice turns. Make slow figure eights at a low level, looking where you want to go.
- Try a gentle slope. Shift down first, then raise the level, as in the hill steps above.
- Ride a short loop. Ride a quiet loop at a low level before your first real trip.
For hosts briefing new riders
If you run or host a shared fleet, five minutes at launch can cover the parts of this article a new rider needs on day one:
- where the level buttons and battery gauge are, and which level the bike starts in
- that the motor helps only while you pedal, and stops when you stop pedaling or brake
- that every level stops helping at the same cutoff speed
- to start low, shift gears before raising the level, and drop the level on crowded paths
- what wind and cold do to the battery, and to dock before the last bar
Then let each rider feel the lowest and highest levels on a quiet stretch, with someone watching the first start.
Colibrino specifies Class 1 pedal-assist bikes with no throttle for its stations; the e-bike fleet page explains why. Its launch-week safety sessions cover how pedal assist works, and the rider guide tells riders to start in a low level until they know how the bike responds.
Example (fictional). In the fictional Larkspur Commons example, launch week runs from day 35 to day 41 with two safety sessions beside the lobby doors. At each session, riders take a bike from a bay, set the lowest level, ride a slow loop of the parking lot, brake to feel the motor stop, and try the top level once on a straight stretch before returning to low. The whole exercise takes a few minutes per rider.
What to do next
Pick the level for the next few minutes of road, not for the whole trip: low by default, up for hills and headwinds, down for crowds, ice and gusts. Before your next ride:
- Learn where your bike’s level buttons and battery gauge are, and which level it starts in.
- Run the pre-ride checklist, including the brake test that shows the motor stops when you brake.
- Put your battery size and route into the range estimator to see what wind, hills and cold will cost today.
- Read the e-bike classes guide for where your bike’s class may ride in Wyoming and Colorado.
- If you are weighing risk, read what the injury data shows about e-bike safety.
- For more on riding in High Plains conditions, browse the riding e-bikes section of The Short Trip.
